This translation service is provided by another company, not by Aldon Corporation. Aldon Corporation is not responsible or liable for translation errors. .

CAUTION: Please read this before reading the label:

We are concerned about the quality of this translation because it is done by computer software. Please understand that some things might sound foolish, insulting, or possibly not make sense. This is because Aldon has no ability to insure the accuracy or appropriateness of the translation. Therefore, we offer this translation for any value that it might give you, but please excuse the errors that might be contained herein. Please see the English language label on the Aldon web page and ask someone to translate it for you in case of any miscommunication. Aldon Corporation takes no responsibility or liability for any miscommunications.

To print this page - type "Control Key" and "P"

ALDON “PREMIUM STRIPPER’ PSTG 11/05

"Premium Stripper" will remove any sealer coating so far encountered, including
urathanes and epoxies. Also excellant for graffitti removal. This product:
• is a controllable semi-gel formula that won't run into baseboards.
• has fume suppression and extended working time before drying.
• is more economical because, unlike a liquid stripper, its active ingredients are held
and working at the surface, instead of soaking in or rapidly evaporating.

Average required is 100–300 sq. ft/gal depending on thickness of coating to be
removed.

When re-sealing, use an Aldon sealer and you won´t need to strip again
For additional information and assistance with your particular flooring material and the
subjects indicated by underlined text, visit the Aldon web site at aldonchem.com.

APPLICATION TECHNIQUE

Patch test first to insure satisfaction with your application techniques and the final appearance.
Maintain adequate cross ventilation until fully dry. Wear solvent resistant gloves, boots, goggles, and
all else necessary for protection of breathing, eyes, and skin.

All strippers only remove sealer at the surface. None will remove the old sealer from below the
surface. Therefore, the new sealer must be compatible with the old sealer remaining below the surface
or you could experience separation (peeling) between the new and the old sealers. If possible, before
proceeding visit the Aldon web site. There is a great amount of helpful information on stripping and
sealing at the PROBLEM SOLVING Section: “Redoing A Previously Sealed Surface"

CAUTION: Safely vent pressure by keeping clear of the cap and liner, unscrew cap slowly and make
a pinhole in any cap liner left on the can. Pouring from a can is easier with the long side down and the
spout up. Store in a cool place. Close container after each application.

• Shake can first, then apply as is using solvent resistant brush or short nap roller to spread over a
comfortable size working area. Do not allow to contact areas other than where finish removal is
desired. Insert disposal instructions here if room does not allow below.

• Let stand until seal blisters (approx. 2 to 3 minutes), but do not allow to dry. If it is drying too fast, it
is not being applied thick enough. Too thin a coating will require more applications and more work.
Careful brush movement will move the “curdled’ sealer out of the way and allow the stripper to
continue working on the next layer below while still active and liquid.

• Remove before dry. Pick up with wet rags, but keep water to a minimum. The careful use of
lacquer thinner can be helpful as a final cleaning step for any sealer/stripper residue. Wait a day, if
possible, to evaluate the results before proceeding to the next step.

• Very thick coatings mean more pounds of sealer to break down, therefore, more stripper
applications may be necessary. After stripping, test floor´s absorption of new sealer before proceeding.
See “Tips & Troubleshooting’ on the product page at aldonchem.com if you do not see the expected results.
RLG: Insert disposal instructions here, or above if no room.

FIRST AID: May be fatal or cause blindness. Immediately drink large quantities of water. Call a physician or Poison
Control Center for safe way to induce vomiting, if called for. IF INHALED - Vapor harmful, particularly to those with
heart problems. If odor is strong or you notice dizziness, headache or eyewatering -STOP - leave area immediately.
If breathing is difficult, give oxygen. IF EYE/MUCOUS MEMBRANE CONTACT OR SKIN IRRITATION: Flush with
water for at least 15 minutes. Remove contaminated clothing & footware. If irritation persists, get medical attention.
IN ALL CASES - Immediately contact a physician & the Poison Control Center! Emergency number 800-535-
5053 or 352-323-3500

DANGER: POISON Contains Methylene Chloride and Methanol. Cannot be made non-poisonous. Avoid if
allergic. Harmful or fatal if swallowed. Vapor harmful. Avoid prolonged contact with skin. Use only in a well ventilated area.
Keep away from heat or open flame as could produce toxic gases. Do not transfer contents to other unlabeled containers.
Close container after use. Non-photochemically reactive. This product contains chemicals known to the State of California
to cause cancer, birth defects, or other reproductive harm. Risk to your health depends on level and duration of exposure.
We believe that there is no significant risk in the normal use of the product. Intentional misuse by deliberately concentrating
and inhaling contents may be harmful or fatal.NOTE: Patch testing is always advisable to insure the results will be as
expected. Each application has a different set of variables and because of possible miscommunication or misunderstanding
of the conditions, final approval, prior to use, must be the responsibility of the user, regardless of recommendations by the
manufacturer or seller. The information contained herein is to the best of our knowledge and belief accurate, however, due to
the fact ALDON has no control over proper surface preparation or application methods, no guarantee as to results is offered,
expressed or implied. ALDON products are inspected before shipment and conform to ALDON'S usual standards of quality
for such goods at the time of shipment to ALDON'S purchaser. All other warranties whether expressed or
implied, including any warranties of merchantability and fitness for purpose, but without limitation thereto,
are expressly excluded. ALDON shall not be liable for consequential or special damages, nor for any
damages in excess of purchase.

ALDON CORP.- Reno, NV. 89504 TM: Trademarks of Aldon Corporation © 2003, Aldon Corporation V.O.C. less than 350 g/l