Tile and Stone Restoration Products  

clean, protect, seal tile - stone - pavers - brick

 

Welcome to the web site of Aldon Chemical

 

 

 

Manufacturer of quality products
for tile and stone since 1984

 

 

 

Bahama Winds Collections

Erwin and Sons - Bahama Winds logo

This page describes replacing the factory sealer for your beautifully handcrafted stone tabletop from Erwin and Sons - Bahama Winds

Erwin and Sons - Bahama Winds stone tabletops

Erwin and Sons - Bahama Winds marble tabletops are factory coated with the Aldon S-B-S Sealer beginning September 1, 2006. This sealer protects well and does a very good job however, like any sealer, it could become damaged from some unusual and severe occurrence. To repair or replace the existing sealer, Erwin and Sons - Bahama Winds recommends using the same Aldon S-B-S Sealer for numerous reasons:

  • S-B-S Sealer's gloss level is customizable by you from low matte to higher gloss.
  • S-B-S Sealer provides increased color enhancement to the marble.
  • S-B-S Sealer protects from acidic liquid etching of marble, as well as the usual staining.
  • S-B-S Sealer does not need to be redone because it does not degrade over time.
  • The Aldon products can be ordered here and shipped to you from any Aldon warehouse throughout the USA and Canada.
  • The Aldon S-B-S Sealer is available in aerosol cans designed specifically for refinishing tabletops.
  • The process of removing the old sealer and then protecting your stone tabletop with Aldon S-B-S Sealer is simple and does not require any special knowledge or tools.
  • If a fabric cover has left a gummy residue behind, see: this page

Here are the instructions for removal of the old sealer and replacement with Aldon S-B-S Sealer:

Step 1 - Removal of the old sealer used prior to September 1, 2006. If you do not know which sealer you have, test a small scraping from an inconspicuous place. S-B-S sealer will dissolve with lacquer thinner and the old sealer will not.

Yes, you do want to remove the old sealer first. That way the new sealer is penetrating into and bonding to the stone, not another sealer.

Strip only a 1/4 section of the total surface area to start. This will give you a "before and after" comparison with the remaining sections to make sure you have removed all the old sealer. Remember that the only reason the new sealer could peel in any area would be because it is bonded to a patch of old sealer that was not removed, and the old sealer was not well bonded to the stone.

clean, protect, seal tile - stone - pavers - brick
Note:
The old sealer is a type that requires the power of "Premium Stripper" to remove it. This product is only available in gallon cans and you will need only a small portion of that to do a tabletop. However, there are additional uses for the product that can be reviewed on its page at  Aldon Products 

  1. Please do not take shortcuts! Each step has purpose and is to make sure you only do this once.
  2. Pour a puddle of Aldon Premium Stripper on a conveniently sized and workable area of tabletop that is not more than 25% of the total area. This is to provide a "before and after" comparison to evaluate the results.
  3. Allow puddle of liquid to sit for as long as possible, but do not let it dry.
  4. Wipe off with a clean white cloth.
  5. You do not need to, but can aid the process with gentle movement of the liquid with a natural (not plastic) fiber bristle brush. You do not need to scrub hard or agitate with the brush. You are only moving liquid around occasionally to aid the process of the "Premium Stripper" breaking down the old sealer.
  6. Evaluate the test area when dry:
    1. Does the stripped area "feel" more like a smooth stone finish and less like a slick coating?
    2. Observe the sunlight bounce off the table top toward you. Does the stripped area look like there is nothing remaining of the old sealer?

    If yes to both, strip the balance of the tabletop

    If no to one or both, strip the test area again and evaluate again.

  7. Rinse once with clean water and wipe dry immediately so that any mineral content in the water is not left behind.
  8. Allow at least 2 hours for complete drying in dry weather before sealing.
  9. If your tabletop looks "faded", do not be concerned. Test a very small area with the Aldon S-B-S Sealer and you should see the color restored. As the sealer does not breakdown, the color should stay strong.

Step 2 - Applying S-B-S Sealer

To see a full video of the sealer stripping / spraying process, click >>
Sealing tabletops
(Available in spray cans)
  1. Follow label directions and note all label cautions.
  2. Do a small test area first.
  3. The goal is to see that you have coated the surface with a thin layer of LIQUID, not a light spray. The liquid will self level. You are not painting!
  4. Your first goal is maximum penetration into the stone. Therefore, allow as much liquid as you think will accomplish that goal.
  5. If the finish is not smooth due to dust particles, buff with very light pressure using #0000 steel wool.
  6. A second sealer application should not be necessary, but can be used to smooth out the finish if needed.
  7. If the gloss is too high for you, or you need to improve a portion, the sealer will liquefy again with lacquer thinner and can be removed or reworked.

The finish you have now created has some interesting features for your consideration:

  • It will clean up easier and be resistant to acidic liquids like wine and fruit juice.
  • It does not need to be redone because it does not degrade over time.
  • It has been used on flooring for 20 years. A table top obviously does not receive the abuse of flooring.
  • Worst case type damage to the sealer (cut with a knife, scorched with a flame or hot metal, etc.) is easily repaired by removing the affected small section with lacquer thinner and reapplication of the sealer.

Note: Use only clean, protect, seal tile - stone - pavers - brick S-B-S Sealer to repair the finish. The concept is "Do not risk incompatibility". We know what additional S-B-S Sealer does with the original S-B-S Sealer, but have no idea what a different sealer might do. A new application of S-B-S Sealer will "melt" the old S-B-S Sealer and they will flow together and tightly bond.

You can order Aldon S-B-S Sealer in convenient aerosol spray cans that are specifically designed for tabletops, back splashes, counter tops, and other small projects. To order this, and any other Aldon products - click here   Immediate Ordering From The Aldon Web Site

 

© Aldon Corporation 2007 All Content, Design, Copy, Code, and Graphics copyright 2007 by
Aldon Corporation
and are protected under applicable USA and international intellectual property law.